News

Press Brake Tooling And Accessories for Air Bending, Bottom Bending, and Coining

In sheet metal fabrication, the same press brake can produce very different results depending on whether it performs air bending, bottom bending, or coining. Each method requires a different combination of tooling geometry, machine tonnage, stroke control, and material compensation.

Selecting suitable Press Brake Tooling And Accessories requires understanding how each bending method controls the sheet metal between the punch and die. The tooling configuration affects more than the final angle. It also influences:

•Inside bend radius

•Required bending tonnage

•Springback compensation

•Surface marking

•Tool wear

•Part repeatability

•Machine loading

A tooling system should therefore be selected according to the forming method, material properties, part design, and available press brake capacity.

What are Press Brake Tooling and Accessories?

Press Brake Tooling and Accessories encompass the components that perform the bending action and the systems that augment the ease and precision of setup and alignment as well as safety.

Basic Elements of Press Brake Tooling

•Upper Punch: Determines the bend angle and the bend profile.

•Lower Die: Helps to support the sheet and forms a V-shaped cavity.

•Tool Holder: Accommodates a punch and a die.

•Adapters: Allow for a change of different tooling standards as well as heights and profiles.

•Segmented Tooling: Used to aid in the bending of short panels, boxes, and similar constructs.

Common Press Brake Accessories

Common accessories consist of sheet followers, tool storage systems, safety guards, tool alignment systems, angle measurement systems, and crowning devices, along with quick-clamping and die holding systems.

While accessories do not influence the direct creation of bend profiles, they do influence the safety of the operator, as well as the accuracy of compensation and the efficiency and ease of installation and changeover of the tooling.

How Air Bending Works

During air bending, the sheet contacts the punch tip and the two shoulders of the V-die. The material does not normally touch the bottom of the die cavity.

The final angle is controlled mainly by punch penetration depth. The V-die opening also has a strong influence on the naturally formed inside radius.

Air Bending Tooling Requirements

For air bending, Press Brake Tooling And Accessories should be selected according to material thickness, tensile strength, desired radius, and flange dimensions.

There are several important considerations in regards to:

•As compared to the finished angle, the punch angle is typically sharper.

•The inside bend radius is heavily dictated by the V-opening.

•The bend radius is adjustable as a function of ram penetration.

•Variation in angle is a function of CNC accuracy and is otherwise predictable.

•The compensation for springback should be specific to the material and process.

Advantages and Limitations

Of the three methods, bending with air requires the least tonnage. Additionally, because air bending requires the least amount of tooling, it is the most flexible in a CNC system.

The drawback is air bending is the most sensitive to springback and also to variations in the thickness of the sheet. Because of this, results can be unreliable if the material is not controlled and if the ram is not consistently positioned.

How Bottom Bending Works

In bottom bending, the sheet is pressed more deeply into the V-die. The material has greater contact with the punch and die surfaces, but the process does not use the extreme pressure associated with coining.

Bottom bending and coining should not be treated as the same process because their tooling loads and material deformation mechanisms differ.

Bottom Bending Tooling Requirements

The punch and die angles must be matched carefully. Tool angles may also include an allowance for expected springback.

Other requirements include:

•Accurate punch-to-die alignment

•A suitable punch nose radius

•Consistent material thickness

•Higher tonnage than air bending

•Tooling matched to the required angle

Bottom bending can improve angle consistency and radius control because the punch geometry contributes more directly to the finished profile. It is often suitable for repeat production using controlled material specifications.

Its restrictions consist of reduced angle adaptability, increased tool wear, and possibly the requirement for different tool sets when there is a change in material thickness or bend angle.

How Coining Works

Coining involves the application of high pressure, and as a result, the punch moves into the bend area and creates significant plastic deformation. The sheet is deformed to nearly the exact configuration of the punch and die.

This method is less common in modern flexible fabrication because it requires considerably more tonnage and places greater loads on the press brake and tooling.

Coining Tooling Requirements

Suitable Press Brake Tooling And Accessories for coining may require:

•Hardened and wear-resistant tool steel

•Closely matched punch and die angles

•Stable forming clearances

•High tooling load capacity

•Sufficient machine tonnage

•Strict alignment and maintenance control

Coining can produce low springback, defined inside radii, and stable bend angles. This increases wear on cutting tools and adds loads to the machine. There are risks to the work surface when this option is used. Dedicated tooling may be required for each angle, which provides less flexibility.

Air Bending vs. Bottom Bending vs. Coining

Comparison FactorAir BendingBottom BendingCoining
Tool contactThree main pointsIncreased die contactHigh-pressure contact
Required tonnageLowMediumHigh
Angle flexibilityHighModerate to lowLow
Springback sensitivityRelatively highModerateLow
Inside radiusMainly influenced by V-openingInfluenced by punch radiusClosely defined by punch
Tool wearRelatively lowModerateRelatively high
Typical useFlexible CNC productionRepeat productionHigh-pressure forming

No bending method is suitable for every part. Selection should consider tolerances, material consistency, production volume, available tonnage, surface requirements, bend radius, and changeover frequency.

How Tooling Geometry Affects Bending

The geometry of Press Brake Tooling And Accessories should match the forming method.

Punch Angle and Nose Radius

Air bending controls the angle through ram depth, while bottom bending requires closer angular matching. Coining largely reproduces the tooling angle.

A punch radius that is too small may cause material cracking, surface damage, local compression, or stress concentration. A radius that is too large can interfere with small-radius parts and short flanges.

V-Die Opening

The V-opening affects:

•Inside bend radius

•Required tonnage

•Minimum flange length

•Surface marking

•Material movement

•Die load capacity

A smaller V-opening does not automatically improve the result. It can increase tonnage and create greater marking or cracking risk.

Die Angle and Shoulder Radius

The die angle and shoulder radius affect friction, sheet movement, and contact marks as the material enters the V-opening.

Accessories That Support Bending Accuracy

Crowning systems counter machine/tooling deflection on long workpieces. For segmented tooling, use quick-clamping systems for better alignment and faster tool change.

Angle measurement systems help solve machine deflection, springback, and the effects of variations in sheet thickness and batch differences. Large or heavy workpieces can sag. Sheet followers help support workpieces to reduce movement.

Choosing Press Brake Tooling and Accessories

Evaluate tooling in regard to the following:

•Material: Springback and tonnage requirements vary with the grade and type of steel, aluminum, and coated sheet.

•Thickness: When evaluating the thickness of the tooling, consider the V-opening, punch radius, the minimum flange, and tooling load.

•Bend Radius: in air bending, the resultant radius is primarily dependent on the material and the V-opening.

•Part Geometry: Consider using segmented, narrow or gooseneck tools for deep boxes, small flanges or return bends to accommodate various obstructions.

•Machine Capacity: Consider the working length, stroke, clamping standard, throat depth and crowning compatibility as well as tooltonnage and tool reach.

Common mistakes include using a V-opening that is too small, not considering the material’s tensile strength, confusing coining with bottom bending, using worn tooling, and exceeding the recommended loading for the tooling.

Tool Maintenance and Inspection

Debris from oil and inspection residue. Inspect punch tips and die shoulders for cracks, chips, dents and wear and check for straightness and alignment.

Press Brake Tooling and Accessories should be stored on appropriate racks to prevent collisions and damage. Record and report any abnormal wear and do not exceed the suggested load limit for the length of the tool.

Which Bending Method is Right for You?

If you prioritize flexibility and prefer a low-tonnage solution that also allows fast production run changes, then go with air bending. For more control over the radius and with higher repeatability of the angle, go for bottom bending. If low springback is a higher priority, and you want to be able to reproduce the geometry of the tooling very closely, then go with coining.

Test bends should be performed to confirm the method. Also, check the tonnage calculations, the tolerances, and to verify the tooling load.

Final Thoughts

Consider the bending method and the corresponding Press Brake Tooling and Accessories for the material and part geometry, the quantity to be produced, and the capacity of the machine.

To help you with the selection of the appropriate press brakes, punches, dies, clamps, and accessories, APEX CNC requests that you submit the material, along with the thickness and bends along with the drawings.

FAQs

Q1. What Press Brake Tooling And Accessories does APEX CNC provide?

APEX CNC offers press brake upper punches, lower dies, segmented tooling, tool holders, adapters, clamping systems, crowning systems, and other bending accessories. Users should confirm the available configurations for their specific press brake model and application.

Q2. Can APEX CNC supply tooling for air bending?

Yes, APEX CNC provides the required tooling, including punches, V-dies, tool holders, and supplemental accessories for air bending, depending on the thickness and tensile strength of the sheet to be bent, the desired bend radius, the length of the bending flange, and the capacity of the machine.

Q3. Does APEX CNC offer tooling for bottom bending?

APEX CNC  provides tooling to support bottom bending, including tooling for matched punch and die angles, tooling with matched radii, alignment tooling, and tooling with adequate load capacity. Additionally, material consistency and springback must be considered.

Q4. Can APEX CNC provide press brake tooling for coining?

Yes, APEX CNC offers tooling for coining. Coining requires high-pressure tooling, along with an adequate combination of tooling hardness, wear resistance, alignment, and load capacity. APEX CNC offers coining tools depending upon the material, the length of the bend, the thickness, the coining profile, and the available press brake capacity.

Q5. Are APEX CNC press brake tools available in segmented designs?

Yes, APEX CNC designs segmented press brake tools for the manufacturing of short segments, box sections, panels, return bends, and for the execution of complex bending sequences. Tools are designed based on the supplied part drawings and the required length of segments.

Contact Us

Get A Free Consultation